I use Hugo, it’s not super complicated.

You basically just define templates in pseudo html for common content (header, nav panel, footer, etc), and then you write your articles in markdown and Hugo combines the two and outputs actual html files.

You also have a content folder for js, css, and images which get output as is.

That’s about all there is to it, it’s a pretty minimalist static site generator.

Hosting wise you can just put it on github pages for free.

Dunno why ppl are down voting you, this is 100% the way.

Architecture as code is amazing, being able to completely wipe your server, re-install fresh, and turn it on and it goes right back to how it was is awesome.

GitOps version controlled architecture is easy to maintain, easy to rollback, and easy to modify.

I use k8s for my entire homelab, it has some initial learning curve but once you “get it” and have working configs on github, it becomes so trivial to add more stuff to it, scale it up, etc.

All headlines for “X” need to just be soecufucally replaced with “Elon Musk”

At this point the two are synonymous.

We need to start phrasing it as:

“Elon musk’s platform…” now.

All the electronics inside are very much capable of combustion.

Your power supply inside the printer body for example can very much fail and burst into flames.

And tbh it’s not that uncommon for that to happen with 3d printers. They’re often made with very cheap parts and prone to cheap work on the inside bits.

Add on how much of a high wattage load they meed to handle for extended periods of time and yeah, sometimes the inner wiring bursts into flames and the whole thing goes up.

I always recommend keeping a cheap lil smoke alarm directly overhead any 3d printer, seriously. Those fuckers can very much spontaneously burst into flames lol

None of this stops the risk of fire.

Once a fire starts, the printer turning off won’t magically stop the fire from continuing to grow.

Printers can fail in all manner of ways.

Also, you should have a venting solution of printing ASA.

It’s pretty cheap to get a proper fire resistant heat cover for a printer.

Just get an emergency “space blanket”, they’re often only a couple bucks and quite good, but very fire resistant.

The fact that they prioritized Helluva Boss (which does follow that type of storyline), on their own YouTube (which they have control over), whereas Hazbin was put onto Amazon Prime with only 8 episodes honestly is what I think caused it.

My gut instinct was to assume they had to agree to certain conditions to get onto Amazon Prime and the money from that is what got us Helluva Boss (which if you haven’t watched that, it’s so fuckin good)

It’s a musical, the songs are catchy.

However I disliked how fast paced the writing was, and how even though it’s called “Hazbin Hotel” and the pilot framed it as a sort of slice of life “bunch weirdos” hanging out and getting redemption, instead that weirdly became the B plot?

Somehow they took the whole story and shifted it over to the B plot and pulled this other big high stakes thing out as the A plot.

That’s not really what I was wanting to watch, and it feels a bit like they hit swapped out the story on me, so I kinda got a bit turned off by that.

I don’t give a shit about some high stakes angels vs demons war end game shit.

I wanted to see interpersonal relationships of weirdos learning to co-exist.

Tl;dr: I was expecting something closer to The Good Place, but instead that got side lined by some huge MCU style plot no one asked for.

… no? I was asking a serious question.

Who tabled this bill, and who is supporting it?

Sometimes its a physical issue in your setup.

Double check your cable, double check the carriage, and double check the rails, look for potential obstructions.

I had one print that kept failing in the exact same place each time, couldn’t figure it out, then I watched it live and the dang ribbon itself was physically catching on a specific part of the geometry mid print and then the print would twist a bit, lol.

Something to consider, I’d recommend visually watching that specific layer when it’s coming up to see if you see something happen.

I use neorg for neovim, specifically I use:Neorg journal today to open up a daily .Norge file that I maintain notes, todo, etc on.

If I need to leave a note for myself for the future, I create a note for that day ahead of time.

Lasse is the original maintainer of XZ, they have been placed back in their position as sole maintainer.

“Jia Tan” was the person who slipped the backdoor into XZ and is now banned.

Lasse has already fixed abd removed the backdoor.

XZ itself is critical software everyone uses (its one of the main compression/decompression programs used on linux)

but the best way to avoid getting them is still to just avoiding stupid shit.

This is fine and dandy on a personal pc, but in a work environment you are now being actively targeted by malicious actors if your company is a good target.

Constantly.

So once you are in that zone you do need some fast acting reactive tools that keep watch for viruses.

For casual users I typically recommend using Cinnamon Desktop, it’s the most Windows-esque UI and will be the easiest for them to pick up and use.

I roll with Cinnamon on Ubuntu and it’s been extremely painless, very simple to get stuff do and shit just works.

Oh I love humor.

I just don’t find very thinly veiled racism funny.

I’m very well aware. It’s still fuckin racist and xenophobic to conflate a person standing too close to an animitronic with women being sexually assaulted.

The article is gross, and a lot of people “just joking” in the comments here are gross.

“Even their robots mistreat women!”

Who is “they”?

What if you found out women in Saudi contributed to the creation of this robot?

What if the robot wasn’t even made by people from Saudi?

The fact you wrote “their”, summarizing an entire nation of people as being the same, is where the Xenophobia/racism kicks in.

“It’s just a joke bruh” is basically your defence.

I don’t get it, it’s not funny.

a country known for its bad treatment of women

Making assumptions about someone/something based off its country of origin sounds pretty xenophobic to me.

The robot didn’t “grope” a woman, it moved its hand as an animitronic, and she was clearly standing right next to it during its animations.

The fact that was blatantly blown into “groping” abd the fact the article felt the need to repeat that it happened in Saudi repeatedly, over and over, should trip the xenophobia alarm.

Consider if it was an article about how an animitronic robot that moved and knocked a man’s wallet out of his hand because he walked to close past it. I.agine if articles turned that into “Jewish made robot tries to steal man’s wallet!” Unironically.

You’d probably look at that and go “yeah okay, that’s pretty fucked up, whyd the do that?” Right?

SMH

Arabic People? The race the robot is designed to look like and is dressed as?

Literally look at the other comments on this thread.