Turned on retraction speed to 11 and i guess it wore down the filament at one part but then managed to push it after some 10 minutes of spaghetti 👌

  • 𝒍𝒆𝒎𝒂𝒏𝒏@lemmy.one
    link
    fedilink
    English
    arrow-up
    8
    ·
    1 year ago

    Anyone aware if that be re-melted or recycled back into filament, or is it pretty much done for?

    If I had a 3D printer this would be nightmare fuel after waiting X hours for the print to complete lol

    • FredericChopin_@feddit.uk
      link
      fedilink
      English
      arrow-up
      11
      ·
      1 year ago

      You kinda get used to them failing.

      Part of the reason my printer just sits there not being used, aside from I collect hobbies for fun, is that it’s a nightmare levelling the bed and getting things dialled in.

      Resin printers don’t have these issues but it depends what you’re printing I guess.

      • marcos@lemmy.world
        link
        fedilink
        English
        arrow-up
        3
        ·
        1 year ago

        Get an automatic bed leveler.

        My printer just sits there, covered. When I want something, I uncover it, clean the printing surface with some alcohol, and tell it to print.

        By the way, resin printers have a completely different set of issues. But yeah, they don’t have those ones.

          • marcos@lemmy.world
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            I have one of those servo sensors that use a microswitch at the end.

            The printer has a sturdy frame build from extruded aluminum. That probably makes a lot of difference. I can take the printer, move it into some other surface, turn it on and print, without leveling issues. Before it I had a wooden one without autoleveling. That one needed leveling before each print.

      • Dept@lemmy.sdf.org
        link
        fedilink
        English
        arrow-up
        3
        ·
        1 year ago

        resin printers have the slight issue of being a chemical hazard and requiring PPE.

      • nothacking@discuss.tchncs.de
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        With resin when a print fails, you just get a half print stuck to the bottom of the resin tank, no spaghetti. The most common cause of failure is the part falling of the lifting platform, typical due to poor supports, but rarelybecause the platform is crooked.

        Leveling is pretty easy on most printers, just loosen the bed, remove the resin tank, placing some thin cardboard in it’s place, lower the platform until it touches the cardboard, and lock it in place.

      • TheHarpyEagle@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Getting an auto leveler was a game changer for me. I still manually level the bed and check the Z offset every two months or so along with other maintenence, but I’ve gone on week long printing sprees without touching the bed springs once.

          • chris@l.roofo.cc
            link
            fedilink
            English
            arrow-up
            2
            ·
            edit-2
            1 year ago

            A few tips that made my prints much better:

            • Check if your rollers are tight enough. None of the axes should wobble if you pull on them
            • Use a PEI sheet for printing
            • Clean the PEI Sheet with Soap and Water at least once
            • Clean with IPA after every print
            • Don’t touch the print bed. The oil on your skin really doesn’t help with sticking.
            • Get yourself a metal feeler gauge with 0.2mm. Level your bed heat nozzel and bed to your normal print temp an then move the nozzel 0.2 mm above the bed. Adjust your Z Offset until you can get the metal gauge undr the nozzle but still feel it touching. that should be your perfect height
            • If you still have problems try all the steps here one after another: https://teachingtechyt.github.io/calibration.html

            I used to have a lot of problems with parts lifting up or my prints being unclean but since I did this my prints look great and stick to the bed.

            • FredericChopin_@feddit.uk
              link
              fedilink
              English
              arrow-up
              1
              ·
              1 year ago

              Thanks for these tips. The next time I’m motivated to print something I’ll definitely take this on board.

    • cynar@lemmy.world
      link
      fedilink
      English
      arrow-up
      11
      ·
      1 year ago

      In theory, you can remelt. Unfortunately, the practicalities mean it’s not viable. Each remelt cycle degrades the plastic itself, so you can only put 20% or so ‘old’ plastic into the mix. Combined with the game of plasticisers (to remove brittleness) and reliable forming, even commercial systems struggle, let alone home ones.

      If environmental concerns are the issue. It’s best to print in uncoloured PLA filament. PLA is corn starch based, and decomposes in a bio reactor environment (it rots quickly in an industrial composter).

      As for speed. They are getting impressively fast. A calibration cube takes around 20 minutes, though less than 5 minutes is possible. My machine is effectively fire and forget. They mess around while you are tuning them in, but once you have a good calibration, they now tend to hold it well. You’ll sit there watching it in fascination for the first few months, but that wears off.

    • spckls@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      You get used to that being a possibility with every print. That’s why you should do everything in your power to have your printer always in shape and operational, although sometimes it will happen no matter what!

      Unfortuneatly, this is just waste, straight to the bin.